TC Share Share this post on Digg Del.icio.us Technorati Twitter T-Cut is offline Quote Quick Reply Reply Bookmarks Digg del.icio.us StumbleUpon Google vBulletin Message Cancel Changes Quick Reply The All the runners were cleaned and sealed to prevent water ingress again. Is it just main beam or dip?, have you checked for power to the headlights with a testlight?......Roadside Always check the basics first ! Cheers Jeffrey in Australia. check over here
The 75 and ZT Owners Club Forums > The 75 and ZT Owners Club Forums > Technical Help Forum Rover 75 T Reg, Lights Not Working But Bulbs OK! Have you had the battery fully disconnected for 45 minutes to let the ecu's reset cures a lot of things.Derek Posted 13 Sep 2011, 20:09 #21 Dallas Personal album Thanks Derek, Unlock the car using then key and operate the handset lock button four times to re-sync the handset. On the MG ZR with a/c most garages will say the a/c has to be degassed etc (more cost) but here we leave the a/c connected.
done the wiggling of the plug Duncan and it sometimes triggers the brake lights to go out and normal rear lights to come on (just as the tapping does). Is there any way to test the existing LSM, should I remove the connector on the top and check for any issues? Posted 09 Dec 2014, 17:58 #7 Jeffrey Hi Guys. You might be right about the FBH, but it doesn't seem quite right.
It is easy to get the LSM out to ensure the multi plugs are fitted properly Fault finding the electronics in the LSM or more likely having it replaced is a Fuse keeps blowing Hunta17 Metro / Rover 100 10 09-08-2011 22:28 Blown fuse and dashboard lights not working? 25G MG ZT / Rover 75 (Sponsored by Rimmer Bros) 1 21-08-2010 10:44 Copyright © 2006-2012 Peter Vickerstaff, . Rover 25 Electric Window Relay Location User Name Remember Me?
Have a look at this photograph it clearly shows the sharp metal edge that the loom rubs against. Rover 25 Electric Window Problems This is not on CAN bus either, and is not actually a relay but another ECU. both rear lights are on as normal but I have the light out icon on the dash, so I unplug wire loom plug from bulb holder and then plug back in Login | Register Forums Gallery View active topics Forums » General Chat » Rover 75 and MG ZT Forum » Snap!
Alarm removal - Can I just rip the siren out and drive home? - Süre: 2:36. Rover 25 Central Locking Fuse Location Posted 13 Sep 2011, 20:36 #24 Dallas Personal album Duncan wrote:Now here's a thought. Bu özellik şu anda kullanılamıyor. We found the rear multimedia modules to have suffered water ingress.
Geri al Kapat Bu video kullanılamıyor. İzleme SırasıSıraİzleme SırasıSıra Tümünü kaldırBağlantıyı kes Yükleniyor... İzleme Sırası Sıra __count__/__total__ How to fix MG Rover Electrical problems - Pektron relay fault - 8/2003 on The EWS module was removed and repaired due to water ingress. Rover 25 Horn Not Working Is there a hospital close by? Rover 25 Horn Relay Location You can only see the switches on the front.
The glovebox is also dark. http://jetpackshield.com/rover-25/rover-200-clock-not-working.html Temperature gauge Chris P, on the MG-Rover.org forum, had a problem were his temperature gauge reading would drop to zero every time he pressed the clutch pedal. Would be very gratefull for any help Edited by Dynamic Dave on 20/02/2009 at 18:47 Tags: technicalissues lights cambelts maintenanceandservicing electrics Like Reply | Report as offensive | Link Fri 20 and no I sadly do not have a multimeter I suppose the first port of call would be to replace both rear bulb holders, then the wire loom plug....... Mg Zr Central Locking Not Working
Posted 11 Dec 2014, 10:45 #16 Duncan Yes, the chances are the connector will look OK even if there are problems. Rover 25 Bcu Removal Remote Handset Handset not working take a look at this site for some tips Battery replacement Prise the handset apart from the key ring end, try not to damage the seal. comeinhandynow 7.947 görüntüleme 46:50 Rod Ramsay internal video for MG Rover employees. - Süre: 6:31.
I gave each light unit a tap and brake lights go out and normal lights come on, I then stitched everything off and then turn lights back on again and all Do check for water ingress arond the wiring loom by the ECU module in the plenum chamber & glow plug module. Do you solve this problem ? Mg Zr Bcu Location Hello and Welcome to justanswer..Im sorry you have had trouble so far - the previous expert is not in the Uk..
The test mode is cancelled by switching the ignition OFF. I ask because this sounds like an inadequate earth which on standard electrics results in lights flashing with indicators. Horn failure Tony Thompson gives us the low down on how to check for this fault here. have a peek at these guys These combinations happen on both sides......
I can access a second hand replacement and try it out. Upper Plenum Water Drain Unblocking And Modification You will find them at the bottom right of the page. Is it parked near a microwave oven? Posted 14 Sep 2011, 20:35 #33 PaulT Personal album And if you go to Maplins you will buy a multimeter for just a few pounds - worth their weight in gold
Tags: indicators radio centrallocking warninglights electrics lights BMW 5SeriesE391996-2003 Related posts vectra 2.6 v6 - vectra speedo lights Don't Try This At Home.. If under the bonnet, that might be the culprit as Steve suggests.