How To Fix Remote Start Not Working Pontiac G6 (Solved) Home > Remote Start > Remote Start Not Working Pontiac G6

Remote Start Not Working Pontiac G6


Reply Mitch says April 26, 2012 at 6:20 pm I am not sure what this could be… Perhaps change the battery in the remote? Neal is online now Pontiac G6 Replaced car battery, now remote start is not Resolved Question: Replaced car battery, now remote start is not working? When you press the remote you can hear a click but it won't start. The blue lights on the remote do flicker when we hit door open, door lock, trunk and start.

This is easily corrected in most cases by simply flipping the switch in the other direction. I noticed that once I pushed the autostart button my park lights did not come and the LED light in the car which controls the autostart was on as a steady We have this exact Compustar remote which came installed in our 2006 ford fusion. Came about today, remote doesn't work.

Pontiac G6 Remote Start Doesn't Work

These are things to check. All I can say it just stopped working for some reason. This just happened to my remote start this weekend… Car starts fine manually but won't start by remote, like it's not cranking long enough… Any ideas or suggestions are welcomed to Reply Brianna says January 23, 2013 at 12:00 pm Mitch: I bought a used 2004 Saturn Ion a couple of years ago with a remote start installed.

Similar Questions2007 Pontiac Grand Prix Remote StartComputer Problem 2007 Pontiac Grand Prix 6 Cyl Front Wheel Drive Automatic When I Try And Remote Start My Car The Horn Will Start ...Asked Let me know if u think u know what's wrong Or any other solutions Or if u know anything mire about the 4 I wrote I don't understand how to do Mark helpful 15 Report Barb answered 2 years ago yup. Pontiac G6 Hood Latch Sensor When you press these buttons, the parking lights should flash two times.

Reply Mitch says November 25, 2012 at 6:30 pm Joe, We do not sell or install that brand. Today it decided not to start for me, nor did the rear lights on the car come on as they normally do before it starts, etc. It likely is a simple fix. Occasionally, losing power (or replacing a battery) may result in the device losing programming.

Reply Mitch says January 6, 2012 at 3:12 pm My guess is that you have some type of transponder bypass included with your remote starter installation. How To Reset My Remote Car Starter I entered the passive mode UNLOCK+TRUNK UNLOCK, and the remote eas working normally.I have a 2011 Ford F-150. I have replaced the batteries in both remotes still nothing . Reply Louis says December 23, 2012 at 12:10 pm Mitch: I have a 2006 Dodge Avenger with remote start.

Pontiac G6 Remote Start Programming

Reply Dave says January 6, 2012 at 5:15 pm I looked around the web at different blogs, and found a similar problem. It was a poor design and the new parts are redesigned. Pontiac G6 Remote Start Doesn't Work Either of these devices will tell the car starter when the hood is open. Pontiac G6 Remote Start Install Remote start will not work if the hood is open or the BCM thinks it is.

If you have further questions, please feel free to contact me directly. weblink Remember, this can only be done twice, and it only lasts for 10 minutes of running time......Would always see Salesmen demonstrate remote start.....then have customer try it......and then later on, someone Automotive Network, Inc., Copyright ©2016 Backup Safety Bluetooth Car Audio Custom Fabrication Navigation Remote Starters Security Truck Accessories Window Tint Mobile EdgeMore Than Just Great Car Audio 1 of the Top Reseal the cap, restart the car, and retry step #1! 2006 Pontiac Grand Prix Remote Start

i searched and nothing seemed to be the same issue I'm having. Sign in to add this to Watch Later Add to Loading playlists... The parking lights come on for two seconds, then turn off, then flash for three times slowly. navigate here Comments John says October 30, 2011 at 8:25 pm Hi Mitch, You gave allot of very valuable information on remote starters and would like to ask you a question.

Many times dealers don't get the remotes when the car is traded in and they buy the remotes with the remote start button even though it doesn't have it. How Do I Know If My G6 Has Remote Start Reply Glenn says February 14, 2012 at 9:09 pm Mitch, found the problem today and it did have to do with the wiring. What I was doing wrong was holding LOCK and TRUNK at the same time until the lights flickered on the remote.

Reply Dave says January 6, 2012 at 2:57 pm I've got a remote starter by auotstar model AS-1725 SH.

Located burnt 30 fuse at remote starter which supplies current to the starter. These separate inputs allow the BCM to actively monitor for a hood ajar switch fault.RVS System OperationThe remote vehicle start (RVS) function allows engine starting while not in the vehicle. I removed the ground wire for 30 seconds, and reconnected with the key out of the ignition, and everything is back to normal. My Remote Starter Stopped Working So i had to leave the vehicle there.

Reply Russ says November 5, 2012 at 1:54 pm Bruce were you able to determine the problem for this? Any idea what could be wrong. Much appreciated. Any ideas.

Sorry about that. When I returned to the truck, the remote would not work at all. I charge about $185 for one with up to 2500' of range. Can anyone help me out?

Will be looking forward to your reply! It really is something that you will need to have someone take a look at. Also Ponchonutty is can go to ANY GM dealership, and ask for a print out of the "Vehicle Build" page......this will list all the SPID codes, and what they mean.....this Reply Orlando says December 6, 2012 at 10:27 am Hi Mitch, i have a 2002 dodge 1500 ram truck with a compustar cm3000.

Do it yourself save $$$$! - Duration: 3:33. If I can't help I will open your Question to other experts.Does the fob still work on the locks? I'm hoping this gives you a start! When i push the door lock button followed by pushing the romote car start the car beeps 2 times and not start.

The blue LED in The receiver is solid and Not blinking as it was when working fine. Mark helpful 8,235 Report Richard answered 4 years ago If it is a factory system, you need to click the lock button first and then immediately click and hold the autostart