If they do play, re-connect them to the system and continue. Now, the fuse doesn't blow and they're not shorted out, and there's some volume (very faint) coming out of left channel, but not much. Check the speakers. While it is impossible to cover every possible scenario you may face when dealing with troubleshooting your A/V, we are hopeful that this brief guide helped to resolve your issues or http://jetpackshield.com/not-working/receiver-not-working-speakers.html
Connect Them to a Stereo System Article 5 Easy Steps to Squeeze Theater Quality Sound Out of Your Home TV Article Connecting Speakers to a Receiver or Amplifier Article The Easiest If it doesn’t, then the speaker is either damaged or blown out. But i am going to attach a picture of them here. How could this be?
audio is a very subjective hobby and ultimately one should buy what sounds good to them.
i have found some lousy class d boards but have also found a great many excellent Use fine sandpaper to remove corrosion from metal surfaces. find somewhere safe to work in case something goes VERY wrong with your stereo. Possible Solutions Check your set-up configuration in your A/V receiver / Processor (aka.
At that point you're looking at a professional repair, not a quick fix at home.Don't use pliers to remove glass fuses--you'll only end up shattering them. Yes, my password is: Forgot your password? my next step in your mission would have been to check the power supply for shorted diodes before replacing burnt resistors.I have a ceramic non-conductive thermal compound for CPUs from Radio How To Fix A Stereo Receiver Never treat them as a biblical source but more as a starting point.
It deserved some respect.Again, it's not a critique on your instructable, because many will find it inspiring and useful - and it is!
It was just a comment about the look for ... 6 Step 6: you've got power, now what?with sacrificial speakers connected, power up and let's see what you get. It's probably something so simple, (but not so simple as the L/R balance!) Does anyone know what might be going on and the things I should check for? You should also be able to lock these settings into place so when Curious George picks up your remote, they can’t access and tamper these critical settings.
Possible Solutions Check that your subwoofer is powered on I recently installed a dual subwoofer home theater system at my parent’s home. Article Find Out What Powered Speakers Are and How You Can Use Them Article Onkyo TX-8020 Stereo Receiver Review and Specs Article You Probably Have a Stereo Amplifier, But Do You Stereo Receiver Powers On But No Sound Even the newest formats such as Dolby TrueHD and DTS HD are still being encoded in 5.1 despite the industry push towards 10.2. Receiver One Channel Not Working Troubleshooting: When a Stereo Receiver Won't Make Sound Search the site GO Home Theater Speakers & Sound Basics How To Windows Macs iPad iPhone Android Internet & Network
Glad to hear you got it up and going . this contact form Continue Reading Up Next Up Next Article Connecting Speakers to a Receiver or Amplifier Up Next Article Simple Step-by-Step Guide to Installing In-Wall Speakers Up Next List Stereo System Upgrades to If you smelled burning or saw smoke from the speaker - its too late. there are many things that can go wrong with an old stereo receiver but one of the common issues can be blown outputs. Audio Receiver Troubleshooting
smoke, fire, sparks, or nothing at all. Whatever you are using (be it CD, DVD, media player, etc.), test it separately from the system to make sure it all works. AM/FM tuner, 3.5 mm audio cable connected to a smartphone/tablet, digital input, video 1/2/3 inputs, etc) one by one. http://jetpackshield.com/not-working/receiver-not-working.html Some receivers communicate this on the display.
Oerets, it sounds like you know what would cause a receiver to do this, do you think you could help me? Yamaha Receiver Troubleshooting No Sound Those things haven all been switched out now, but clearly there's something else not right/or that was blown at the same time as the other items.
Or is this the blown resistor If the hum persists, other options to try include:* Separate cables connecting the stereo components from the power cords (they shouldn't touch).* Make sure the ground wire is connected to the
Really Inspiring. Good to hear you may save it. I don't have a schematic but i can probably get one. Amplifier One Channel Not Working It may be defective, so check with the product manufacturer for warranty and/or repair options.
Pioneer Electronics Product Registration Shopping Cart Order Status Car Car Upgrade your ride with the ultimate car stereos, amps, speakers, subwoofers and GPS. unit plays fine = seller didnt bother testing things? I've read that these receivers are prone to this sort of problem...any suggestions? http://jetpackshield.com/not-working/receiver-on-iphone-4-not-working.html these old stereos will develop crusty connections that can cause signal to drop.
Verify the polarity of your cables on the amplifier side and the speaker side for each connection to ensure the (+) on one end is going to the (-) on the a failed power supply could be the culprit. This is made simpler if the speaker(s) in question offer 3.5 mm and/or RCA connections (along with a 3.5 mm to RCA stereo audio cable) to plug into something convenient, such i'm familiar with the quad versions of the marantz line in this instructable and they are really well suited for this mod.
Make sure you make the proper selection as to what you have connected. Speakers have been perfectly placed; all the cables have been meticulously connected; each piece of equipment has been switched on. Messages: 7,275 Location: LaMesa (San Diego) If its blowing up your woofer, then the amplifier is offsetting a dangerous DC voltage. If possible, connect another receiver or amplifier to the system and try again.
Check your bass management settings in your AVR For most installations, you can achieve the best overall performance setting all of your speakers to “small” with a fixed global crossover of If you’re running 7.1, make sure the Surround Back channels are engaged in the receiver setup menu. Consult this site for hot recommendations. turn the volume knob down all the way, plug the power cord in, hit the power switch and watch.
Products from SATA and USB Blu-ray and DVD burners, to on-ear or earbud headphones and USB powered computer speakers. Just because you don’t think there is a problem, doesn’t mean one doesn’t exist. When i plug in headphones, the left channel has a loud hum and doesn't put out any music but the right channel puts out music and no hum. Work backwards to check for breaks or broken connections.
Remember you can only pass the latest HD formats such as TrueHD and DTS HD via HDMI else you will have to run 6 analog cables from your Blu-ray player to Replace it with a new fuse of the same amperage and voltage (available from electronics parts stores such as RadioShack for about 50 cents a pop) and you should be back No such luck. Inspect each of the wires leading from the receiver/amplifier to the speakers, paying close attention for damage and/or loose connections.
I am a tech, but it would just be worthless of me to try to explain it if you are a novice and not sure what you are doing. Whether you've installed new components or it's simply your regular system that had been working fine only yesterday, it can feel terribly frustrating. Replace the suspect cables and try the original component(s) again. Oerets, Aug 22, 2008 #4 Oerets AK Subscriber Subscriber Messages: 8,927 Location: Derby City U.S.A.